DATASHEET
5mm Silicon PIN Photodiode , T-1 3/4
PD333-3C/H0/L2
Notes
1.
Lead Forming
?
?
?
?
?
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it
may break the LEDs.
Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs
are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.
2.
Storage
?
?
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life limits
are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a
nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can
occur.
3.
Soldering
?
?
Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,
and soldering beyond the base of the tie bar is recommended.
Recommended soldering conditions:
Hand Soldering
DIP Soldering
Temp. at tip of iron
Soldering time
Distance
300 ℃ Max. (30W Max.)
3 sec Max.
3mm Min.(From solder
joint to epoxy bulb)
Preheat temp.
Bath temp. & time
Distance
100 ℃ Max. (60 sec Max.)
260 Max., 5 sec Max
3mm Min. (From solder
joint to epoxy bulb)
?
?
?
?
?
Recommended soldering profile
laminar wave
Fluxing
Prehead
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to
room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
Release Date:2013-05-30
10:50:50.0
www.everlight.com
8 : 3
Revision Copyright ?
LifecyclePhase:
2010, Everlight All Rights Reserved. Release Date : May.27.2013. Issue No: DPD-0000154
Expired Period: Forever
相关PDF资料
PD42-21B/TR8 PHOTODIODE PIN IR 1.8MM RND BK
PD42-21C/TR8 PHOTODIODE PIN IR 1.8MM RND CLR
PD438B PHOTODIODE PIN IR 4.8MM CYL BK
PD438C/S46 PHOTODIODE PIN IR 4.8MM CYL CLR
PD438C PHOTODIODE PIN IR 4.8MM CYL CLR
PD4859J5050S2HF POWER DIVIDER 4800-5900MHZ 0805
PD6080J5050S2HF POWER DIVIDER 6000-8000MHZ 0805
PD638B PHOTODIODE PIN IR FLAT SIDE BK
相关代理商/技术参数
PD333-3C2 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Silicon PIN Photosiode, T-1 3/4
PD333-3C-H0-L2 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Silicon PIN Photodiode , T-1 3/4
PD333-3H0 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Silicon PIN Photodiode , T-1 3/4
PD333-3L2 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Silicon PIN Photodiode , T-1 3/4
PD333-3L3 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Silicon PIN Photosiode, T-1 3/4
PD3340 制造商:OHIO BUCKEYE 功能描述:
PD3340MT102 制造商:SEI Stackpole Electronics Inc 功能描述:Ind Power Unshielded Wirewound 1mH 20% 100KHz 800mA T/R
PD3340MT221 制造商:SEI Stackpole Electronics Inc 功能描述:Ind Power Unshielded Wirewound 220uH 20% 100KHz 1.6A T/R